Can I Set Up A Bath Tub Myself?
Can I Set Up A Bath Tub Myself?
Blog Article
We've stumbled upon the article about How to Install a Bathtub below on the net and decided it made good sense to share it with you in this article.
Installing a bathtub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably challenging project. If the old bathtub is conveniently available, the project can relocate easily; if you have to open a wall to eliminate the old bathtub and also place the new bath tub, the job is a lot harder. In either case, the task is within a house handyman's skills, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. Make certain you have certified yourself for the work and also are comfortable attempting it. As opposed to employing a service provider to take control of a halfway-completed project, it is far better to take into consideration utilizing one prior to you start. Opportunities are you may need a professional plumber to make tube links.
This post will certainly help you install a brand-new tub in your bathroom if you have actually already acquired a new tub and also don't need to transform the plan of your previous supply of water pipelines.
Your tools and also product checklist need to make up the following:
Planning for the Installation
To start with, the sustaining frame provided with the bathroom should be fitted (if called for) according to the maker's guidelines. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you make use of all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last position.
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted gain access to that is frequently the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, put the bath tub in the called for placement. The wood boards are helpful in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the bath tub until the spirit level checks out level.
To install taps, fit the bottom of the outermost versatile faucet port to the proper supply pipeline by making a compression join; then do the exact same for the various other tap.
Turn on the water system as well as inspect all joints and new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise inspect the overflow outlet and the typical outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's user's manual. Tiling and also securing around the tub ought to wait up until the tub has been used at least when as this will settle it right into its last setting.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in place with the maker provided backnut. When the tap is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The former kind needs to be connected to the faucet finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to break an inflexible seal, causing the water to pass through the wall between the bathroom and also the tiling, leading to issues with wetness and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes and also cartridges, and can sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the tub with water prior to sealing, to allow for the motion experienced when the bathtub is in use. The sealant can fracture fairly early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles using waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that piece of writing about A Step-by-Step Guide to Installing a Bathtub when perusing the internet. If you enjoyed our article kindly remember to pass it around. Many thanks for your time. Kindly pay a visit to our site back soon.
Order Repair
Report this page